Rich, sorry about the goes a lot harder but it does.Late this afternoon I shorted out middle cell so it ran on six.Didn't have time to measure amps and the way the cell is made can't measure volts across cell with only six going,but I can say the vehicle goes a heck of a lot better.I know that isn't very scientific but time and construction were agianst me.
regards,
Mos
SERIES FAILURE
25 posts
• Page 2 of 2 • 1, 2
by Looking In » Fri Jul 18, 2008 8:11 am
Rich (Looking In)
((((Is it really so difficult to tell a good action from a bad one? I think one usually knows right away or a moment afterward, in a flash of regret.)))) BOOM
((((Is it really so difficult to tell a good action from a bad one? I think one usually knows right away or a moment afterward, in a flash of regret.)))) BOOM
- Looking In
- Regular Poster
- Posts: 367
- Joined: Thu Dec 22, 2005 11:06 am
by dhho » Thu Jul 24, 2008 11:17 pm
Just a quick update on my cell I have it running on 6 cells with a mix of 240 grms naoh to 1 liter of water and it is drawing 5 amps and is making good gas.I will post actual amount of gas when I can get someone to help me measure it.This seems to be the most amps I can get it to draw,but I guess its not going to overload anything in the electrics department.Still haven't got camera for photo (sorry)
regards,
Mos
regards,
Mos
- dhho
- Regular Poster
- Posts: 23
- Joined: Fri May 30, 2008 11:11 pm
- Location: Kangaroo Island (AU)
volume gage
by okumaguru » Fri Jul 25, 2008 4:33 am
I found a video on You tube and built one from it. The video is called "#41 Refinements to the gas rate measuring tool."
Although I would expect the easiest way to measure would be to purchase a gage from a welding supplier.
Just though I would share about the gage on You tube.
Tim
Although I would expect the easiest way to measure would be to purchase a gage from a welding supplier.
Just though I would share about the gage on You tube.
Tim
- okumaguru
- Regular Poster
- Posts: 58
- Joined: Sun Nov 05, 2006 8:20 am
- Location: mid-Missouri
by dhho » Wed Aug 06, 2008 2:16 am
Today I finally got someone to help measure my output of hho and I am getting 800ml per minute at 5 amp cold, although it doesn't seem to change much when hot.
Regards,
Mos
Regards,
Mos
- dhho
- Regular Poster
- Posts: 23
- Joined: Fri May 30, 2008 11:11 pm
- Location: Kangaroo Island (AU)
by chemelec » Wed Aug 06, 2008 10:29 am
If you Email Me, the Word "ELECTRONIC" MUST appear in the Subject Line.
My NEW Website is:
http://chemelec.com
My NEW Website is:
http://chemelec.com
- chemelec
- Regular Poster
- Posts: 646
- Joined: Sun Jan 23, 2005 1:53 pm
- Location: B.C. Canada
The circuit works
by kumaran » Wed Aug 06, 2008 10:03 pm
Regards,
Kumaran
(Knowledge without action is useless, action without knowledge is foolish)
Kumaran
(Knowledge without action is useless, action without knowledge is foolish)
-
kumaran - Regular Poster
- Posts: 525
- Joined: Tue Oct 03, 2006 9:06 pm
- Location: Kuala Lumpur, Malaysia
25 posts
• Page 2 of 2 • 1, 2
Return to Hydrogen Production via Electrolysis
Who is online
Users browsing this forum: No registered users and 24 guests