Magnet Motor Demonstrated at Delft University

[Nailer]

Magnet Motor Demonstrated at Delft University

video included of actual magnetic motor running on its own power , taken apart and examined and reassembled .

Is this the future of motors?

http://x-journals.com/2010/magnet-motor ... niversity/

[Nailer]

Magnet Motor Demonstrated at Delft University
Sterling Alan reports on Pure Energy Systems News: Turkish inventor, Muammer Yildiz, recently demonstrated his magnet motor that he alleged runs on the power of magnets alone at a University in the Netherlands. The motor is shown turning a fan at a high speed, and no wires can be seen going to the device; then the device is disassembled in front of the group.

Putting it into some perspective, remembering that most of the demonstrations of magnet motors over the years have proved to be frauds, Sterling adds: “How many magnet motor stories have we had here in our news service in the last eight years? Several a month. How many times have we featured a story of of an all-magnet motor being demonstrated at a University? Never.â€

[Nailer]

I would love to see the plans/diagrams for the motor published on the web as this design , if true and not a scam should be given out for free to all so they are set free from the clutches of Big Oil.

I hope the inventor has body guards 24/7 so Big Oil can't knock him off. He needs to take it to the MSM and bring it out for all to see and have it proven that his design is not a scam.

[Nailer]

a link to what I believe are the drawings of this set up..

http://v3.espacenet.com/publicationDeta ... cale=en_EP

[Nailer]

http://www.rexresearch.com/yildiz/yildiz.htm

This device claims to produce over-unity --- apparently by means of Homopolar Generators.




http://www.muammer-yildiz.com
http://muammeryldz54.spaces.live.com/Pe ... 02_owner=1



--------------------------------------------------------------------------------

WO 204/091083

A System which Generates Electrical Power via an Accumulator that Provides the Initial Motion for the System

Muammer YILDIZ

Abstract

This is a portable system that generates electrical power via an accumulator that provides the initial motion for the system. Two batteries are used in this system and the system is kept working via the initial motion provided by these batteries. There is no need for another transformer. This device works using its own mechanism and there is no need for additional devices. In this way, a continuous electrical power generation is possible. This device can work without connecting it to a network so it is possible to use it at places where electricity does not exist. Moreover, when connected to the entry of a building, the need for a network is avoided. This system generates electrical power independent of a network.

Description

A system which generates electrical power via an accumulator that provides the initial motion for the system.

This is a portable system that generates electrical power via an accumulator that provides the initial motion for the system.

Already existing systems can generate electrical power of whose duration depends on the lifetime of the battery. In these systems, the battery has to be reloaded in order to restart the system. 12V electrical power provided by the batteries used in cars are increased to 220 V via transformers.

Two accumulators are used in out invention. The system works on a continuous basis after initial startup via these accumulators. There is no need for another transformer. Our system, which generates electrical power, does not need any other devices and it keeps on generating energy via its own mechanism. Also, the system works without connecting it to a network. Thus, it can be used at any place where no electricity exists. Nevertheless, when this system is connected to the entry of the buildings, there is no need for an additional network. The system can produce electrical power independent of a network.

Below are the explanations of the figures that provide a better understanding about this invention.

Figure 1 --- Schematic view of the system.



Numbers on the schema:
1. --- Accumulator
2. --- Regulator
3. --- Big gear
3/1 --- Starter dynamo
4. --- Small gear
4/1-2. --- Feedback dynamo
5. --- Small gear
5/1-2-3. --- Feedback dynamo
6. ---Contactor
7/1-2. --- Commitatris [Commutator]
8. --- 19 DC input
9. --- 24 DC input
10. --- 580 DC output
11. --- Switch
12. --- Shunt
13. --- Rectifier
14. --- Capacitor
15. --- 2.5 mm cable
16. --- Collctor
17. --- Charcoal [Carbon]
18. --- Fixing clamps (+)
19. --- Fixing clamps (-)
20. --- Lamp
21. --- Conjector
22. --- Starter dynamo
23. --- Feedback dynamo
24. --- AC dynamo
25. --- Magnetic switch
26. --- Pulley
27. --- Pulley
28. --- V pulley
29. --- 380 V current output
30. --- 220 V current output

This invention is a system that starts working via the motion of alternator. There exist two accumulators (1), and the first motion provided by the accumulator is carried to the regulator. Contractor (6) keeps the starter dynamo working by disconnecting the accumulator (1) once the regulator (2) is put in. The voltage coming from the accumulator (1) passes through the regulator and the start dynamo (3/1) starts working and thus the feedback alternators via the gears ( 4/1-2 – 5/1-23-3 ). Feedback dynamo starts sending pure DC current to regulator via shunt (12), capacitor (14) and diode (13). It connects all the current that reaches to the regulator in 4 seconds and sends to the contactor (6). Accumulator (1) is put out by this current that reaches to the regulator. This current is transformed to the started dynamo (3/1). There becomes a transformation within the system. In case of electricity shortage, it keeps on working by using the current generated by the commitatris (7/1).

Via the starter dynamo (3/1), DC is generated in the alternators which are connected to the gears and this current is transformed to the commitatris (7/1-2) and DC voltage is generated at commitatris (7/1-2).

Second System

3 x 24 DC voltage is transformed to the second starter dynamo (22). Once the start dynamo works (22), a feedback dynamo (23) having a pulley system and a feedback dynamo (24) generating alternative current starts working. The feedback dynamo (23) starts feeding back; the feedback dynamo (24) which generates AC is independently generating 6 KV, 18 Amp, 50 Hz current. Moreover, first system produces 24 DC and 580 DC current on its own.

The bigger the gears are, the more current is generated.

This system, which is subject to our invention, can be used at any place. You can use it at places where there exists no electricity, or at places such as villages, cities, buildings, greenhouses where there is not network. Moreover, network is no more a must. Instead of a network, you can use our system. There is no need for gasoline when this system is used in vehicles.


--------------------------------------------------------------------------------

Technische Universiteit Eindhoven [Eindhoven Technical University]
Department of Electrical Engineering, Electromechanics and Power
EUT_JD2005_2.doc (7-28-2005)

Experiments on an Apparatus Intended to Generate Electricity without Physical Connections to Other Power Sources

by

J.J. Duarte

This technical note aims at describing a test I personally conducted in Izmir, Turkey on July 17, 2005. The purpose of the experiment was to check the energy balance with respect to input and output of an apparatus, which was the embodiment of the invention described in international patent WO 2004/091083 A1.

The apparatus was confined inside a metallic box, and I was allowed to inspect everything outside this box. However, in order to protect the core ideas of the invention, I was not supposed to check all the details of the internal parts. According to the inventor the apparatus is predominantly a mechanical system, without any kind of energy storage inside the box like batteries, accumulators, flywheels, combustion motors, chemical or radioactive reactions. I believe the intentions of the inventor were in good faith.

The experimental setup was quite simple, as shown schematically in Figure 1. It consisted of placing the box with unknown contents, from which DC voltages and currents were expected to be generated, on a table in the middle of a room. From the box, a cable with two terminal contacts was available for connecting electrical loads. I placed measurement instruments between the box output terminals and the load. The load consisted of an ordinary AC-DC inverter, this inverter being connected to an incandescent lamp. The working principle of the inverter and the lamp type were not relevant for analyzing the results, because the output power delivered by the box was measured immediately after the output terminals. Photographs of the setup are included in Appendix A.

Figure 1: Experimental Setup



After a short start procedure, the metallic box together with the lead were fully isolated from the environment (in what concerns other physical contacts like cable connections to the public mains) during the whole duration of the measurements. This situation is in agreement with the description given in the international patent [ WO 2004/091-83 ] mentioned above. Since the energy input entering the apparatus was quite modest, as it will become clear further in this note, the main issue was then to measure the delivered energy output.

I had prepared the power measurements with care, by using reliable instruments I personally brought with me from my own university laboratory. In order to measure the DC voltage directly out of the positive and the negative electrical terminals I used two different voltmeters in parallel, one analog (constructed with permanent magnets and wires) and another digital (that employs electronic circuits to acquire and to display the measured values). These instruments are based on completely different working principles. Also for measuring the DC current coming out the positive terminal and entering back into the negative terminal, I placed two ammeters in series, again one analog and the other digital. If electromagnetic waves would interfere with the measurements, they would disturb one or the other instrument, but not all four pieces at the same time in the same way.

Before starting the experiment, no kind of audible noise was being produced by the apparatus. Also, I measured the voltage differences between the internal and external connection points, and no potential differences between the internal and external connection points, and no potentials were found. So far as I could observe, the apparatus was completely at rest.

The start procedure consisted of connecting a small 12V DC lead-acid accumulator to two contact points inside the box, during a short time interval (see Figure B1 in Appendix B). I observed this time interval with the help of my own watch, and it was more than 5 seconds, but less than 10 seconds. In later calculations it is reasonable to consider this start time interval as being equal to 8 seconds. After that, no other energy input was connected to the box by means of cables.

Immediately after the start procedure I could hear noise as produced by rotating parts inside the box. The inventor communicated that a stabilizing time interval of about 10 minutes should be respected before switching on the load (inverter plus lamp). During this interval it was possible to observe in both voltmeters that DC voltage was being generated on the terminals, which decayed slowly from 12.9 V DC to 12.5 V DC. The displayed values in the analog and digital instruments were in good match. After 10 minutes I switched on the DC inverter.

In the following hours I observed and registered by hand the values of voltages and currents displayed by the instruments. The displayed values were quite stable; therefore I decided to register them first after 15 minutes, later at each half hour.

From time to time I sensed the internal parts in the box with my hands, looking for temperature gradients, but I could not perceive any noticeable temperature rise with respect to the ambient. After 5 hours I took the decision to stop the measurements.

Results are given in Table 1. The displayed values of both voltmeters and both ammeters were in good agreement (in view of the precision of the instruments), as it can be seen in Table 1. For this reason, I dare to conclude that the results I’ve registered are reliable, to the best of my knowledge.

From Table 1 it is possible to see that the generated output voltage and current remained fairly constant during the 5 hours test.

Table 1



Remarks:

So far the experiment has been described. The following comments are my own subjective interpretation.

Power calculations based on the registered values of voltages and currents in Table 1 lead to the conclusion that much more energy is delivered by the box, which was completely isolated from the environment, than the possible initial energy input used to start the process. For instance, the energy output after 5 hours is approximately given by

( 12.25 V ) x ( 2.3 A ) x ( 5 x 60 x 60 s ) = 507 kJ

Therefore, in order to input this same amount of energy into the box during the start procedure, the current that would have been drawn from the small 12 V lead-acid accumulator for the duration of 8 seconds is found to be

507 kJ / ( 12 V ) x ( 8 s ) = 5280 A

which is physically not possible to realize considering the volume of the accumulator and the simple connector contacts shown in Appendix B!

Considering the inventor’s assurance that the apparatus is mainly a mechanical device, and that no kind of energy storage was implemented inside the box, it isn’t clear where the measured excess of energy out of the box is coming from --- whether out of electromagnetic fields or as the result of some anomaly associated with rotating bodies in terms of inertia. This is a most interesting phenomenon, which deserves further attention.

After analyzing the results in detail, together with the drawing and explanations provided by the inventor (see Appendix C), it was possible to recognize from the schematics certain mechanical structures, the so-called homopolar machines, turning at high speed of rotation.

This is a really exciting idea because a link could be established between the apparatus under observation and a famous experiment performed in 1831 by Michael Faraday, the inventor of the electrical machines. In the academic literature this old experiment is known as the Paradox of Faraday’s Disk.

Indeed, many other scientists hypothesize about the possibility of constructing homopolar machines with efficiency above 100% (see, for instance, the paper of Brice DePalma, "On the Possibility of Extraction of Electrical Energy Directly from Space" in the academic journal Speculations in Science and Technology, Sept. 1990, Vol. 13, No. 4…) [ see also: http://www.rexresearch.com/depalma/depalma.htm ]. However, up to the present time nobody has demonstrated in a convincing way a practical application of the principle. Perhaps the inventor has discovered the missing link in these machine; who knows?…

Of course, the straightforward way to check this possibility would be to inspect the contents inside the box. However, the inventor is only willing to allow that after a solid commitment with a research institution or an industrial partner.

So, the next step would be to exclude the possibility of some kind of conventional electrochemical energy processing inside the apparatus. For this purpose the realization of another experiment, similar to the one described above, would be advisable, but not without long run-time of measurements. The results should convince that, indeed, it is not possible to get the same energy output with the best commercially available battery. Therefore, a new experiment may take many days (about 4 or 5) to be executed.

Eindhoven
28 July 2005

[Nailer]

more links.


Links:

http://www.youtube.com/watch?v=ybn--DsyzBk --- Video

http://www.ocean-star.org/german/presse2.html
http://www.ocean- star.org/center.html
www.haber7.com/haber.php?haber_id=71457
http://www.milligazete.com.tr/index.php ... ws&id=6643
http://www.haberarsivi.com/haber.asp?id=6863
http://www.inndir.com/haberler.php?id=36997
http://samsun.meb.gov.tr/haberler/yenil ... IM=kpy.pdf
http://www.zaman.com.tr/webapp-tr/haber ... rno=130993
http://www.forumca.net/showthread.php?t=63173

[Jehu]

Humm, interesting

[tireboy]

wooo this is good. have tried building a magnetic motor. I am seeing a lot of scammers in my daily quest to alternative energy, but what I have learned is that energy is not free, perpetual motion machines do not exist, everything is taken from somewhere and put elsewhere.