Hence the term: PIC Chips.
AlaskaStar
Statistics: Posted by AlaskaStar — Sun Sep 02, 2007 4:01 pm
]]>
like a modified pulse width? I seem to remember somthing about the Trace C-60 being used as a load control.
What's a PIC?
Statistics: Posted by 12volt dan — Sun Sep 02, 2007 9:27 am
]]>
Using a PIC, I can discharge in cycles and extend the battery life almost indefinitely, as well, the surface equalization charge will allow the bursts to continue long after the battery should be toast. the amperage is lost over time, but not the voltage. it is the strangest phenomenon to have a battery completely drained of amps, but still show good fully charged volts.
I sent the E-mail a while back, but I think I included my Phone number. I talked to Mark, and he gave me your number. it was no good, so at that time I sent the e-mail to the only address I have for you. it was the one that you sent me a message from. I really would like to call you, as it is quite important. I am prepping a vehicle to run 100% "off GRID" for a journey from here to Virginia Beach. this means: Electric, and Hydrogen Fuel. I have some technical questions, I do not intend this to be a permanent fixture, as my time spent in any given province or state will be mere hours. I cannot get this system certified to comply with US EPA regs, or the CARB specs. it's cleaner than the Tesla Motors car, in that in operation it uses NO CARBON FUEL. Tesla must re-charge their cars....mine? recharge as I go. It's a combination of Generator, Batteries, Electric Motor, Hydraulics, Hydraulic Motor, and Hydrogen Fuel. I might put a solar panel on the roof for fun. maybe even tow a trailer with my Cushman Trike- for use as a runabout vehicle.
Whichever e-mail address you sent me a message from, is the one that I sent my Phone Information to. Thanks a BUNCH!
AlaskaStar
Statistics: Posted by AlaskaStar — Sun Sep 02, 2007 3:00 am
]]>
]]>
Fortunately there have been some recent advances in technology which are easy to implement and have proven very effective.
Look into "desulfators" and "desulfator circuits." They are very simple circuits which utilize components very similar to those used in the PWM; they are quite easy to make and test and adjust; and they consume very little power.
Once a home made desulfator is installed in conjunction with your normal charging setup you should find that "equalization" as it is normally thought of is no longer necessary.
The desulfator will keep your battery bank in top condition and even restore those batteries that have lost some of their capacity.
The number of off-gridders who have discovered this "secret" is growing rapidly.
Let us all know what your experiences are after you've tried it!
Statistics: Posted by SeaMonkey — Tue Aug 14, 2007 1:27 am
]]>
I had them charging for a few days to get them up and diconnected them to see how they were. The dropped to 12.30 over the next night which isn't so good. The good news is they have stayed there for 2 weeks now without dropping any further so there's some life yet. I'm not going to hook them up with the main batteries for obvious resons but I think I can charg them from the aux side of the MX-60 and use them for some kind of seperate back up system.
On the generator shed front,Ive managed to take some batts from the old house bank,an odd panel and the old controller and gave the shed it's own power supply
The batts tucked under the engine quite well for space saving which I need since this shed is only 100 sq ft including the walls (1 ft thick cordwood)
and the controller seems to like it in here,It has a use again
Lots more to do yet before this thing is running but we're making progress again
Statistics: Posted by 12volt dan — Sun Jul 01, 2007 9:58 am
]]>
Ive also plugged in a small fridge since our needs have expanded. it's rated at 85 watts cont. but I think it's drawing more than that. In a few hours it should be cold and the constant draw will cycle. I should be charged up by then and I can get a better feel of what this thing uses
Film at 11
Statistics: Posted by 12volt dan — Sun Jun 10, 2007 11:06 am
]]>
We don't live in Alaska
I was able to rearrange some of the 8-D's to a lower shelf and bring in the first 9 batts. Now I build another shelf underneth at the other end and squeeze another 9 under there.
As soon as my backs up to it
Statistics: Posted by 12volt dan — Wed Jun 06, 2007 9:52 pm
]]>
]]>
Bob
This week I went from being a singe guy to having a partner and my son begin new lives here. This will put the 12volt lifstyle to the test I'm thinking. I was planning to install septic and well pump (the wells drilled allready) this summer anyway so the push will be on now as well as getting the cogeneration setup running by fall when the temps and the solar levels drop.
It will be a busy time indeed
Statistics: Posted by 12volt dan — Sun Jun 03, 2007 10:02 am
]]>
]]>
]]>
]]>
I just built myself a family but not the conventional way
Your not going to believe this one
Statistics: Posted by 12volt dan — Fri Jun 01, 2007 7:37 am
]]>
I want to get these in in the next couple of weeks for that reason. I have looked at moveing some of the 8-D's to a lower location under the shelf and making a new shelf to the left of the others.
This will get me to 4180 amp hrs total,plenty enough for me
Statistics: Posted by 12volt dan — Wed May 02, 2007 9:30 pm
]]>